Rural FAQs
How do I install an A to Z Post?
First mark out the correct post spacing. Next augur or dig a hole 300mm wide by 650mm deep. Fill the hole with a wet mix concrete mix and push the post into the concrete mix allowing the mix to flow up into the inside of the post.
How do I install a Gate Post and fit a gate?
First mark out the correct Gatepost location. Place the post in the hole and mark out the hinge location. Fit the hinge to the post making sure you have sufficient adjustment to correctly position the gate once the post is set. Place the post in the hole and fit the rails into the post. Before the rails are slid into the post block the ends of the rails with adhesive tape. Brace the post if required. Drive a single 12mm Steel Re-enforcing bar through the centre of the post into the soil then core fill the post with a wet mix concrete. After the concrete has set you can bolt the gate to the hinge.
Other companies say that coloured fencing will fade rapidly, will Think Fencing products fade?
All of AtoZ Fences coloured products are made from a PVC acrylic composite, the PVC makes up the structure of the profile and the Acrylic capping layer provides the colour. This is very important as coloured PVC that is not capped will fade very fast. Whilst we use the best products available today a 10-year-old fence will not look like a 10-week-old fence. (It will however look significantly better than a 10-year-old timber fence)
The style of fence that I want is not listed in your brochure, can you make other styles?
A to Z has a dedicated design and fabrication division that is equipped to assist you with all aspects of design and manufacture. If you have an idea we can make it a reality. Just send a basic sketch or an image of the style of fence you are trying to replicate. (We can also match colour-Subject to Minimum orders)
Can you make matching Gates?
Yes, AtoZ Fences can make almost any gate design you want, Swing gates can be made up-to 2.4m each panel and sliding gates can be made up-to 6m long! All gates come with hardware made by D&D Technologies and are also 100% Australian made.
How long will my fencing last?
AtoZ sources profiles manufactured in Australia for over 10 years and tested in the harshest of conditions. Our supplier Think Fencing Pty Ltd employs modern technologies to ensure your fence will outlast a timber fence and look just as good after many years.
Will my fencing easily scratch?
The colours we use on our fencing products are not just a coating, they are a specific layer of Mechanically and Chemically bonded polymer that has been incorporated into the profile during manufacture. The result is colour that is durable, and is scratch and scuff-resistant.
What if my fence goes up/ down a hill?
Standard fencing provided by AtoZ Fences can already accommodate a 1-3 degree rake. Anything larger than this will require increasing the length of the slot by rasping it out on site or have AtoZ Fences provide custom routed posts and rails. AtoZ Fencing can rake or step to accommodate a slope.
Does a professional need to install my fence?
Our fences are suitable for DIY. The most challenging part is to concrete posts into the ground and level the fence. After that everything simply “locks in”. Any fencing contractor or “handy” person should easily be able to install our fencing. A to Z Fencing will provide detailed installation instructions and our staff are always happy to assist with any questions or concerns you or your installer may have.
How do the rails and pickets lock in?
Picket, Horizontal Slat and Post & Rail fences have a crimp on the rail and pickets facing outward. The crimp is designed to allow you to push the rail into the post but not pull out. AtoZ Fences hires the crimping tool to create the crimp. Mystique Privacy requires the rails to be tek-screwed in.
What if I need to shorten a Panel?
A to Z will always round up your requirements to the next panel ensuring you have enough materials for your job. All PVC components can be cut using a hack-saw, or aluminium cutting blade to enable you to shorten a panel. When cutting rails, ensure you leave at least 30mm on each side to slide into the posts. If rails need to be cut to shorten a panel, you may need to re-crimp the rail with the supplied crimping tool.
Is this fencing safe for horses and livestock?
PVC Fencing is safe for Horses and Livestock. Think Fencing does recommend adding a additional electric conductor along the fence run. Post and Rail will flex before breaking, minimising potential harm to horses and livestock.
What if I want to put Mesh onto my fence?
AtoZ Fences has a Post & Rail Mesh option available. You can also attach mesh to our other fence styles. You will need to construct an end assembly to tension wires for attaching mesh. AtoZ Fences can supply end assemblies and screw in clips to attach mesh.
What if I want to electrify my fence?
An electric stand off can be screwed onto the post using suitable tapered self tapping screws
How do you go around corners?
For sufficient tension, AtoZ Fences recommends starting and stopping with a new Insulstrainer and End Bracket on each corner and end.
PVC and recycling
PVC is widely used in guttering, pipes and ducting in NZ.
Manufacturers locally take clean pvc to recycle and re purpose into new pipe and products. These manufacturers are Marley NZ located in Auckland and Christchurch, Iplex pipelines located in Palmerston North and Christchurch and RX Plastics located in Hamilton and Ashburton. It is highly recommended that you make contact first to assess logistics to get your used pvc to these locations and the guidelines around the condition of the product prior to despatch.
How do the rails and pickets lock in?
Picket, Horizontal Slat and Post & Rail fences have a crimp on the rail and pickets facing outward. The crimp is designed to allow you to push the rail into the post but not pull out. AtoZ Fences hires the crimping tool to create the crimp. Mystique Privacy requires the rails to be tek-screwed in.
